Innovative 7000 Series Radial Arm Review
official, the desktop has been liberated! No longer is your poor desk a captive of 50 pound blocks of beige and glass! The standard TFT LCD display was the first step in this
liberation; with less bulk than a CRT it freed up a good foot or two of desk
space. By adding a desk or wall mounting adjustable armature next, an LCD
display can effortlessly float above the entire desktop, yielding the much
coveted "Zero Footprint" many have been looking for.
Of course if you are going to suspend a $700 or $1400USD LCD display above a desk, or from a wall you had better be sure whatever is holding it up is strong, and well built.
One such solution
to LCD flat panel support is the 7000 Series Radial Arm from Innovative
Office Products (lcdarms.com). It goes for about $180USD and takes about 15 minutes to assemble, and setup.
With solid black power-coated cast aluminum
construction, the 7000 Series is remarkably good looking, and able to
support LCD display's weighing from 8-22lbs. The adjustable armature
supports both 100mm and 75mm VESA mounting-point compatible LCD displays by
means of two interchangeable steel adaptor plates.
|The arm has a vertical range of 14". That means 7" above or below horizonal as shown in the bottom image here.|
The armature features three pivots able to rotate a
full 360° for greater flexibility when moving the LCD display left, right, or
backwards/forwards. The entire armature can collapse into about 3" of space or
extend up to 24" from the mounting point. An adjustable gas cylinder in the main
arm acts like a counter balance so the 7000 series arm can be 'tuned' to support
any type of LCD flat panel perfectly. With that gas cylinder properly adjusted
the monitor becomes weightless, allowing the user to easily position it where
The armature has a vertical range of 14" (7" up and
7" down from horizontal) and a tilt mechanism directly behind the LCD panel can
tilt 200° to support even wider viewing situations. arm has a vertical
range of 14", meaning that the LCD display will remain stationary if you move it
up a few inches.
To keep things simple, we mounted the 7000 series
radial arm, along with the very nice Samsung 191T LCD display, to the edge of
desk. The unit is versatile enough to be mounted to a wall, desk, slat wall,
panel system wall, or even via a thru-desk mount. The same tools and accessories
are used for most of these mounting configurations which further simplifies
Mounting an LCD on the 7000 series
The unit arrives in a long flat box unassembled,
but instantly ready to. Setting up the armature is simply a matter of deciding
where to put it, and then assembling the four or so main components with the
included allen key.
After the stand has been removed from the LCD
display (a Samsung 191T in our case) it needs only be mounted to the right sized
adaptor plate (100mm or 75mm). The final task is to tuck the wires from the LCD
display away in the base of the armature sections and that's it. The cable ways
are easy to get at and keep the monitors power and video signal cables from
draping all over the desk.
One more thing makes the 7000 series radial arm the
pinnacle of easy adjustment - a set screw at the base of the main arm adjusts the
pressure on an internal gas cylinder which counter balances the weight of the
LCD display. One that adjustment has been made, the display can be moved into any
vertical position and just sit there as if it were weightless. If the screw is
not adjusted the arm will have a tendency to always rise up.
Other small set screws make using touch
sensitive LCD panels an easier proposition because they add more friction to the
joints of the armature - increasing the amount of force needed to knock it out
Contents of Article: Innovative Office Products Radial Arm
— Innovative 7000 Series Radial Arm Review
Build Quality - Solid
||Use the power of Google to search all of PCSTATS and the PCSTATS Forums. Tell us what you think of this new feature - FEEDBACK?|